[PLUTO-help] problemi con porte usb

[Andrea!]

Ciao,
sul problema delle porte usb non ho progredito di una virgola,
adesso però mi capita di leggere questo con dmesg:

[...]
usbcore: deregistering driver xdslusb
usbcore: registered new driver xdslusb
usbcore: deregistering driver xdslusb
usbcore: registered new driver xdslusb
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
usb 2-1: usbfs: interface 0 claimed while 'cxioctl' sets config #1
divert: not allocating divert_blk for non-ethernet device ppp0
application firefox-bin uses obsolete OSS audio interface
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb 1-5: new high speed USB device using address 5
usb 1-5: device not accepting address 5, error -32
usb 1-5: new high speed USB device using address 6
usb 1-5: device not accepting address 6, error -32

Le prime righe si dovrebbero riferire al driver del modem
adsl via usb, che ho penato non poco per far vedere,
mentre le ultime immagino colpiscano il nocciolo
del problema!!!

Ciao,

andrea

Tommaso Massimi mi ha detto il 11/27/2005 06:25 PM:

>On 11/27/05, Andrea! <andrea.storto a tiscali.it> wrote:
>  
>
>>Uhm,
>>mi dice:
>>....
>>scsi0 : sata_promise
>>scsi1 : sata_promise
>>...
>>e per l'usb (dmesg | grep usb)
>>eusbcore: registered new driver usbfs
>>usbcore: registered new driver hub
>>usbcore: registered new driver hiddev
>>usbcore: registered new driver usbhid
>>drivers/usb/input/hid-core.c: v2.0:USB HID core driver
>>SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
>>SELinux: initialized (dev usbdevfs, type usbdevfs), uses genfs_contexts
>>usb 2-1: new full speed USB device using address 2
>>usb 2-2: new full speed USB device using address 3
>>usbcore: registered new driver xdslusb
>>/usr/cxacru_new/module2/xdslusb.c: udsl_usb_init: driver version 2.0pre1
>>kobject_register failed for xdslusb (-17)
>>[<c02763d4>] usb_register+0x3b/0x7a
>>usbcore: error -17 registering driver xdslusb
>>drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0
>>alt 0 proto 2 vid 0x03F0 pid 0x1904
>>usbcore: registered new driver usblp
>>drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
>>usb 4-2: new low speed USB device using address 2
>>input: USB HID v1.10 Mouse [1241:1177] on usb-0000:00:03.2-2
>>usbcore: deregistering driver xdslusb
>>usbcore: registered new driver xdslusb
>>usbcore: deregistering driver xdslusb
>>usbcore: registered new driver xdslusb
>>usb 2-1: usbfs: interface 0 claimed while 'cxioctl' sets config #1
>>...
>>e tutti i vari ohci etc caricati!
>>    
>>
>
>
>dopo aver inserito la penna alla fine della scritte di dmesg
>dovrebbe esserci roba tipo questa:
>
>usb 4-5: new high speed USB device using ehci_hcd and address 3
>SCSI subsystem initialized
>Initializing USB Mass Storage driver...
>scsi0 : SCSI emulation for USB Mass Storage devices
>usb-storage: device found at 3
>usb-storage: waiting for device to settle before scanning
>usbcore: registered new driver usb-storage
>USB Mass Storage support registered.
>  Vendor: TinyDisk  Model: 2003-12-09        Rev: 2.00
>  Type:   Direct-Access                      ANSI SCSI revision: 02
>usb-storage: device scan complete
>sda: Unit Not Ready, sense:
>: Current: sense key: Unit Attention
>    Additional sense: Not ready to ready change, medium may have changed
>sda : READ CAPACITY failed.
>sda : status=1, message=00, host=0, driver=08
>sd: Current: sense key: Unit Attention
>    Additional sense: Not ready to ready change, medium may have changed
>sda: Write Protect is off
>sda: Mode Sense: 03 00 00 00
>sda: assuming drive cache: write through
>SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
>sda: Write Protect is off
>sda: Mode Sense: 03 00 00 00
>sda: assuming drive cache: write through
> /dev/scsi/host0/bus0/target0/lun0: p1
>Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
>
>hai provato a dare  prima un
>modprobe -v  usb-storage ?
>
>Ciao
>  
>
>------------------------------------------------------------------------
>
>_______________________________________________
>pluto-help mailing list
>pluto-help a lists.pluto.it
>Per gestire la propria iscrizione alla lista: 
>http://lists.pluto.it/listinfo/pluto-help
>