[PLUTO-help] problemi con porte usb

[Tommaso Massimi]

On 11/27/05, Andrea! <andrea.storto a tiscali.it> wrote:
>
> Uhm,
> mi dice:
> ....
> scsi0 : sata_promise
> scsi1 : sata_promise
> ...
> e per l'usb (dmesg | grep usb)
> eusbcore: registered new driver usbfs
> usbcore: registered new driver hub
> usbcore: registered new driver hiddev
> usbcore: registered new driver usbhid
> drivers/usb/input/hid-core.c: v2.0:USB HID core driver
> SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
> SELinux: initialized (dev usbdevfs, type usbdevfs), uses genfs_contexts
> usb 2-1: new full speed USB device using address 2
> usb 2-2: new full speed USB device using address 3
> usbcore: registered new driver xdslusb
> /usr/cxacru_new/module2/xdslusb.c: udsl_usb_init: driver version 2.0pre1
> kobject_register failed for xdslusb (-17)
> [<c02763d4>] usb_register+0x3b/0x7a
> usbcore: error -17 registering driver xdslusb
> drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0
> alt 0 proto 2 vid 0x03F0 pid 0x1904
> usbcore: registered new driver usblp
> drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
> usb 4-2: new low speed USB device using address 2
> input: USB HID v1.10 Mouse [1241:1177] on usb-0000:00:03.2-2
> usbcore: deregistering driver xdslusb
> usbcore: registered new driver xdslusb
> usbcore: deregistering driver xdslusb
> usbcore: registered new driver xdslusb
> usb 2-1: usbfs: interface 0 claimed while 'cxioctl' sets config #1
> ...
> e tutti i vari ohci etc caricati!


dopo aver inserito la penna alla fine della scritte di dmesg
dovrebbe esserci roba tipo questa:

usb 4-5: new high speed USB device using ehci_hcd and address 3
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
  Vendor: TinyDisk  Model: 2003-12-09        Rev: 2.00
  Type:   Direct-Access                      ANSI SCSI revision: 02
usb-storage: device scan complete
sda: Unit Not Ready, sense:
: Current: sense key: Unit Attention
    Additional sense: Not ready to ready change, medium may have changed
sda : READ CAPACITY failed.
sda : status=1, message=00, host=0, driver=08
sd: Current: sense key: Unit Attention
    Additional sense: Not ready to ready change, medium may have changed
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
 /dev/scsi/host0/bus0/target0/lun0: p1
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0

hai provato a dare  prima un
modprobe -v  usb-storage ?

Ciao