[PLUTO-help] PCMCIA combo USB2.0/Firewire & hard disk esterno USB2.0 --ATTO II---

[Mauro Bonacini]

Grazie per la tempestività dei suggerimenti!

- L'alimentazione l'ho collegata dopo che mi sono reso conto che non era 
opzionale...:) (Ma la PCMCIA non dovrebbe passare un pò di 
potenza???Mistero degli standard informatici).

- Ho provato a scaricare i moduli e a ricaricarli a mano ma il risultato 
è stato deludente. L'output di dmesg è chiaro: riconosce il bridge ma no 
riesce ad accedere all'HD dando una pletora di errori che indicano il 
mancato riconoscimento della periferica.

usb 3-1: new high speed USB device using address 2
scsi7 : SCSI emulation for USB Mass Storage devices
  Vendor: Genesys   Model: USB to IDE Disk   Rev: 0002
  Type:   Direct-Access                      ANSI SCSI revision: 02
SCSI device sda: 58605120 512-byte hdwr sectors (30006 MB)
sda: test WP failed, assume Write Enabled
sda: assuming drive cache: write through
 sda:SCSI error : <7 0 0 0> return code = 0x70000
end_request: I/O error, dev sda, sector 58605112
Buffer I/O error on device sda, logical block 7325639
SCSI error : <7 0 0 0> return code = 0x70000
end_request: I/O error, dev sda, sector 58605112
Buffer I/O error on device sda, logical block 7325639
 sda1 sda4 <SCSI error : <7 0 0 0> return code = 0x70000
end_request: I/O error, dev sda, sector 10490440
Buffer I/O error on device sda, logical block 1311305
SCSI error : <7 0 0 0> return code = 0x70000
end_request: I/O error, dev sda, sector 10490440
Buffer I/O error on device sda, logical block 1311305
 >
Attached scsi removable disk sda at scsi7, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi7, channel 0, id 0, lun 0,  type 0
sda : READ CAPACITY failed.
sda : status=0, message=00, host=7, driver=00
sda : sense not available.
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
USB Mass Storage device found at 2
usb 3-1: USB disconnect, address 2
ehci_hcd 0000:07:00.3: qh 0fd2f080 (#0) state 1
sda : READ CAPACITY failed.
sda : status=0, message=00, host=1, driver=00
sda : sense not available.
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
 sda:<3>scsi7 (0:0): rejecting I/O to device being removed
Buffer I/O error on device sda, logical block 0
scsi7 (0:0): rejecting I/O to device being removed
Buffer I/O error on device sda, logical block 0
scsi7 (0:0): rejecting I/O to device being removed
Buffer I/O error on device sda, logical block 262143
scsi7 (0:0): rejecting I/O to device being removed
Buffer I/O error on device sda, logical block 262143
scsi7 (0:0): rejecting I/O to device being removed
Buffer I/O error on device sda, logical block 0
 unable to read partition table
usb 3-1: new high speed USB device using address 3
scsi8 : SCSI emulation for USB Mass Storage devices
USB Mass Storage device found at 3

L'errore potrebbe stare nei driver scsi  ma non so cosa fare.

Chi ci capisce qualcosa!?!

Grazie molte.

Mauro Bonacini